How To Wire 24 Volt Trolling Motor Plug

While small and medium trolling motors use a single 12v marine battery, larger trolling motors use larger 24v and 36v systems, and require 2 or 3 marine batteries, accordingly. So if you have never done it before and you want to give it a shot, here is how to go about it.

12/24 Volt Trolling Motor Wiring Diagram Database

Connecting two 12v batteries in series provides the 24v power source required to run your motor.

How to wire 24 volt trolling motor plug. The 2 batteries already have a short jumper cable between them to make 24 volts at the receptacle. These larger motors and multiple batteries are wired in a series pattern, and optimally, the circuit breaker should be wired within 4 of your battery. 4 wire trolling motor plug elimination texas fishing forum

In this case, you need two 12v deep cycle batteries,. Place the receptacle into a hole and fasten it with the screws. Loosen the two terminals on the circuit breaker supplied with the trolling motor.

Push the trolling motor wires through the openings at the end of the cover. In the 24 volt scenario you would wire the batteries individually without a jumper between the two. This sends 2 separate 12 volt sources to the outlet.

Tighten the two strain relief screws at the rear of the housing. 4 wire 12 24v trolling motor plug black marinco power products. For your trolling motor, you only need two wires, +24volts and ground.

December 27, 2021 by masuzi. When it comes to wiring a 24v trolling motor, the good news is that it’s not complicated and you don’t need to hire a professional to do it. Trolling motorwiring motorguide 24 volt motor wiring diagram schematic 3 wires coming from plug 4 wire elimination a purchase is made help with the connectpro batteries system 24v texas fishing forum how to chicago forums battery favorite expertise minn kota 12 model 767 question trollbridge24 information and guide charge v 10.

The boat war wire for batteries in parrallel (12 volts) to the motor. Everything you need to wire your motor. Marinco 12vcp 40a 3 wire connectpro trolling motor plug socket the chandlery.

You might isolate the bare wire ends (if you have stripped too much). This wiring was done through the male side of the plug. Red is typically +24 volts, orange is typically +12 volts, and white or black is typically ground.

I'll show you how to wire up a 24v trolling motor plug. Place aside and save for step 4. Also see my youtube on installing a trolling motor receptacle:

Remove the strain relief by loosening the two strain relief screws. Last year my dealer already replaced my factory tm wiring with two 6 gauge wires running from my 2 tm batteries to the bow receptacle. Get the necessary tools and equipment to wire your 24v trolling system.

Both the 24v and 36v trolling motor wiring. On trolling motors with three wires (12/24 or 24/36v), cut out the third hole in the cover. Pull the cover off the plug by pulling it back away from the blades.

4 wire trolling motor plug elimination 24v trolling motor plug 3 wire connectpro trolling motor plug conversion of a 12 24v system to. If you do not have a marinco 12/24 volt plug or are using the “12” volt wiring then you would have your batteries wired as you show in. The problem with the socket and plug that you have now, is that the socket and plug is not really sized to handle the 6 gauge wire that is normally used with the 60 amp trolling motor plugs.

I had a toought time figuring it out like you so i opened the plug to find junpers installed between the wires from the batteries making it in parrellel. 1) look at the plug on the motor and draw yourself a picture noting the wire colors for the three terminals. Rig rite trolling motor male plug 10 ga 3 420 for online.

Then, use the voltmeter to measure the voltage at every wire combination that is coming from your plug wire. 4 prong trolling motor plug wiring diagram. So, when you find the +24 volt wire and the ground wire in your trolling motor plug that you plugged into the socket, connect those to your trolling motor.

The two batteries are wired to the receptacle as shown in fig. The 24v trolling motor wiring schematic often shows two 12v batteries connected in a series. They will typically be red, orange and black, or red, orange and white.

Remember, 40 amps on each 12 volt trolling motor battery is still only 40 amps, when the batteries are connected in series to form 24 volts. So here is what you need to do: This trolling motor plug, cat.

Slide the red wire from the motor over one of the terminals and tighten it down. How to wire 24 volt trolling motor plug. The marinco plug then “jumpers” it in the plug making it 24 volt for the motor.

Do the same with the battery leads. See our detailed guides on: Now, you need to attach the motor power leads to the male end (the plug itself), and the battery leads to the female end (receptacle).

Connect the trolling motor’s power leads into the male end (the plug) and the battery leads to the female end (the receptacle). The wiring is not complex, and you can wire your motor using the schematics below without a professional. 24v trolling motor plug install.

24 volt connection when using the marinco 12 plug walleye message central. Slide the red jumper wire, which is short section of conductor wire, over the other terminal on the circuit breaker and tighten it down. A 60 amp circuit breaker is in place at the battery.

4 Prong Trolling Motor Plug Wiring Diagram 37